Difference between revisions of "Short Notes on Linux Administration"

From PaskvilWiki
Jump to: navigation, search
 
(One intermediate revision by one user not shown)
Line 49: Line 49:
 
== Find and Mark Bad Blocks ==
 
== Find and Mark Bad Blocks ==
  
<pre>$ sudo backblocks -sv /dev/sdX > ~/bad-blocks-list
+
To test partition <tt>/dev/sdXN</tt> (such as, <tt>/dev/sda1</tt>) for bad blocks simply run:
$ fsck -l ~/bad-blocks-list /dev/sdX</pre>
+
<pre>$ sudo backblocks -sv /dev/sdXN > ~/bad-blocks-list
You can run the test also just on a partition, simply by selecting <tt>/dev/sdXN</tt> instead of just drive <tt>/dev/sdX</tt>.
+
$ fsck -l ~/bad-blocks-list /dev/sdXN</pre>
 +
 
 +
== Using TLP to Optimize Battery Lifetime ==
 +
 
 +
<pre># check TLP status and system info
 +
$ sudo tlp-stat -s
 +
 
 +
--- TLP 1.1 --------------------------------------------
 +
 
 +
+++ System Info
 +
[...]
 +
 
 +
+++ TLP Status
 +
State          = enabled
 +
Last run      = 09:13:49,    403 sec(s) ago
 +
Mode          = battery
 +
Power source  = battery
 +
 
 +
# get battery information
 +
$ sudo tlp-stat -b
 +
 
 +
--- TLP 1.1 --------------------------------------------
 +
 
 +
+++ Battery Status
 +
/sys/class/power_supply/BAT0/manufacturer                  = CPT-COS
 +
/sys/class/power_supply/BAT0/model_name                    = L17C4PB0
 +
/sys/class/power_supply/BAT0/cycle_count                    = (not supported)
 +
/sys/class/power_supply/BAT0/energy_full_design            =  45520 [mWh]
 +
/sys/class/power_supply/BAT0/energy_full                    =  44540 [mWh]
 +
/sys/class/power_supply/BAT0/energy_now                    =  37370 [mWh]
 +
/sys/class/power_supply/BAT0/power_now                      =  20057 [mW]
 +
/sys/class/power_supply/BAT0/status                        = Discharging
 +
 
 +
Charge                                                      =  83.9 [%]
 +
Capacity                                                    =  97.8 [%]
 +
 
 +
# CPU temperature and fan speed
 +
$ sudo tlp-stat -t
 +
 
 +
# CPU info
 +
$ sudo tlp-stat -p
 +
 
 +
# warnings
 +
$ sudo tlp-stat -w</pre>

Latest revision as of 09:19, 21 November 2019

Reset Compiz to Default Settings

gconftool-2 --recursive-unset /apps/compiz

and restart.

Enable and Start sendmail

If you're getting "stat=Deferred: Connection refused by [127.0.0.1]" log messages from sendmail, try adding the following line to your /etc/mail/sendmail.mc file:

DAEMON_OPTIONS(`Port=smtp, Addr=127.0.0.1, Name=MTA')

under the "General defines" section.

Also, make sure the sendmail daemon is running:

ps aux | grep sendmail

If not, run it using

sendmail -bd -q1m

where -q parameter chooses how often the email queue's new messages should be processed (here, every minute).

To test if this all works, use

echo -e "Subject: Hello\nTesting the mailer..." | sendmail -f test@test.com myrealaddress@mail.com

The advantage of sendmail over mail is that the from address need not be a valid email address... well... advantage?

Installing sendmail

On most systems, sendmail comes as a package, and typically gets started during the boot from the init.d/rc.d scripts.

If you want/need to start sendmail manually, or it has died, use

sendmail -bd

or, for debugging purposes

sendmail -bD

that will start sendmail daemon, but will keep it in foreground, so you can see its output.

Sending Emails using sendmail

The easiest way is to create the message file with all necessary definitions, e.g.

To: Mr. Recepient <recepient@hosting.com>
Subject: This is a fine example of a subject
Date: 2011-08-15 20:00:00 +0000
From: Mr. Sender <sender@hosting.com>
Content-Type: text/plain; charset=utf-8
Content-Transfer-Encoding: 8bit
Content-Disposition: inline
User-Agent: My email service

The body of the message comes here, after a single blank line...

and then feed this file to sendmail:

sendmail -t < message_file.txt

Find and Mark Bad Blocks

To test partition /dev/sdXN (such as, /dev/sda1) for bad blocks simply run:

$ sudo backblocks -sv /dev/sdXN > ~/bad-blocks-list
$ fsck -l ~/bad-blocks-list /dev/sdXN

Using TLP to Optimize Battery Lifetime

# check TLP status and system info
$ sudo tlp-stat -s

--- TLP 1.1 --------------------------------------------

+++ System Info
[...]

+++ TLP Status
State          = enabled
Last run       = 09:13:49,    403 sec(s) ago
Mode           = battery
Power source   = battery

# get battery information
$ sudo tlp-stat -b

--- TLP 1.1 --------------------------------------------

+++ Battery Status
/sys/class/power_supply/BAT0/manufacturer                   = CPT-COS
/sys/class/power_supply/BAT0/model_name                     = L17C4PB0
/sys/class/power_supply/BAT0/cycle_count                    = (not supported)
/sys/class/power_supply/BAT0/energy_full_design             =  45520 [mWh]
/sys/class/power_supply/BAT0/energy_full                    =  44540 [mWh]
/sys/class/power_supply/BAT0/energy_now                     =  37370 [mWh]
/sys/class/power_supply/BAT0/power_now                      =  20057 [mW]
/sys/class/power_supply/BAT0/status                         = Discharging

Charge                                                      =   83.9 [%]
Capacity                                                    =   97.8 [%]

# CPU temperature and fan speed
$ sudo tlp-stat -t

# CPU info
$ sudo tlp-stat -p

# warnings
$ sudo tlp-stat -w